Were you interested in know-how about A Step-by-Step Guide to Installing a Bathtub?
Setting up a bathtub isn't specifically rocket science, but it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a brand-new one is also a moderately tough job. If the old bathtub is conveniently accessible, the project can move immediately; if you need to open up a wall surface to remove the old tub as well as position the brand-new bath tub, the job is much harder. In either case, the job is within a house handyman's abilities, although you will certainly require a helper to move out the old tub as well as embeded in the brand-new one. See to it you have actually certified on your own for the work and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed task, it is far better to take into consideration employing one before you begin. Chances are you may need a professional plumber to make tube connections.
This short article will assist you set up a brand-new tub in your shower room if you have already purchased a new tub and don't need to change the arrangement of your previous water supply pipelines.
Your devices and also product list must make up the following:
Getting ready for the Installation
Firstly, the sustaining framework supplied with the bathroom must be fitted (if called for) according to the supplier's guidelines. Next off, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps device to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (often supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the supplied washing machines.
Connect the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom ought to currently be ready to be suited its final position.
Removing Old Touches
If you need to change old taps with new ones as a part of your installment, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be rather bothersome because of the limited access that is usually the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipes to the taps. Have a towel ready for the continuing to be water that will come from the pipelines. Once the supply pipes have actually been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any kind of old sealing compound.
Prior to moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Mounting the Bathtub
Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wood boards are helpful in uniformly spreading out the weight of the bath tub over the location of the boards instead of focusing all the weight onto four little factors.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the spirit level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the proper supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water supply and check all joints and new pipework for leaks as well as tighten them if required. Fill up the tub as well as likewise inspect the overflow electrical outlet as well as the typical electrical outlet for leakages.
Lastly, take care of the bathroom paneling as explained in the maker's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used at least once as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the tap and the other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will require reducing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next, position the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular tap connectors. The previous kind ought to be connected to the faucet ends first, tightening up only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bathroom satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is necessary as the installation can move sufficient to break an inflexible seal, triggering the water to penetrate the wall surface between the bathroom as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and also are capable of securing spaces approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to sealing, to permit the motion experienced when the bathtub remains in use. The sealer can crack relatively early if you do not take into consideration this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also quickly available on the market. It is a good idea to fit the floor tiles making use of water-resistant or water resistant adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I stumbled upon that write up about A Step-by-Step Guide to Installing a Bathtub when browsing on the internet. Sharing is nice. Helping others is fun. Thanks so much for taking the time to read it.
Contact Us Today